D7net
Home
Console
Upload
information
Create File
Create Folder
About
Tools
:
/
lib
/
modules
/
4.4.0-1128-aws
/
build
/
drivers
/
net
/
usb
/
Filename :
Kconfig
back
Copy
# # USB Network devices configuration # comment "Host-side USB support is needed for USB Network Adapter support" depends on !USB && NET menuconfig USB_NET_DRIVERS tristate "USB Network Adapters" default USB if USB depends on USB && NET if USB_NET_DRIVERS config USB_CATC tristate "USB CATC NetMate-based Ethernet device support" select CRC32 ---help--- Say Y if you want to use one of the following 10Mbps USB Ethernet device based on the EL1210A chip. Supported devices are: Belkin F5U011 Belkin F5U111 CATC NetMate CATC NetMate II smartBridges smartNIC This driver makes the adapter appear as a normal Ethernet interface, typically on eth0, if it is the only ethernet device, or perhaps on eth1, if you have a PCI or ISA ethernet card installed. To compile this driver as a module, choose M here: the module will be called catc. config USB_KAWETH tristate "USB KLSI KL5USB101-based ethernet device support" ---help--- Say Y here if you want to use one of the following 10Mbps only USB Ethernet adapters based on the KLSI KL5KUSB101B chipset: 3Com 3C19250 ADS USB-10BT ATEN USB Ethernet ASANTE USB To Ethernet Adapter AOX Endpoints USB Ethernet Correga K.K. D-Link DSB-650C and DU-E10 Entrega / Portgear E45 I-O DATA USB-ET/T Jaton USB Ethernet Device Adapter Kingston Technology USB Ethernet Adapter Linksys USB10T Mobility USB-Ethernet Adapter NetGear EA-101 Peracom Enet and Enet2 Portsmith Express Ethernet Adapter Shark Pocket Adapter SMC 2202USB Sony Vaio port extender This driver is likely to work with most 10Mbps only USB Ethernet adapters, including some "no brand" devices. It does NOT work on SmartBridges smartNIC or on Belkin F5U111 devices - you should use the CATC NetMate driver for those. If you are not sure which one you need, select both, and the correct one should be selected for you. This driver makes the adapter appear as a normal Ethernet interface, typically on eth0, if it is the only ethernet device, or perhaps on eth1, if you have a PCI or ISA ethernet card installed. To compile this driver as a module, choose M here: the module will be called kaweth. config USB_PEGASUS tristate "USB Pegasus/Pegasus-II based ethernet device support" select MII ---help--- Say Y here if you know you have Pegasus or Pegasus-II based adapter. If in doubt then look at <file:drivers/net/usb/pegasus.h> for the complete list of supported devices. If your particular adapter is not in the list and you are _sure_ it is Pegasus or Pegasus II based then send me <petkan@users.sourceforge.net> vendor and device IDs. To compile this driver as a module, choose M here: the module will be called pegasus. config USB_RTL8150 tristate "USB RTL8150 based ethernet device support" select MII help Say Y here if you have RTL8150 based usb-ethernet adapter. Send me <petkan@users.sourceforge.net> any comments you may have. You can also check for updates at <http://pegasus2.sourceforge.net/>. To compile this driver as a module, choose M here: the module will be called rtl8150. config USB_RTL8152 tristate "Realtek RTL8152/RTL8153 Based USB Ethernet Adapters" select MII help This option adds support for Realtek RTL8152 based USB 2.0 10/100 Ethernet adapters and RTL8153 based USB 3.0 10/100/1000 Ethernet adapters. To compile this driver as a module, choose M here: the module will be called r8152. config USB_LAN78XX tristate "Microchip LAN78XX Based USB Ethernet Adapters" select MII select PHYLIB select MICROCHIP_PHY help This option adds support for Microchip LAN78XX based USB 2 & USB 3 10/100/1000 Ethernet adapters. To compile this driver as a module, choose M here: the module will be called lan78xx. config USB_USBNET tristate "Multi-purpose USB Networking Framework" select MII ---help--- This driver supports several kinds of network links over USB, with "minidrivers" built around a common network driver core that supports deep queues for efficient transfers. (This gives better performance with small packets and at high speeds). The USB host runs "usbnet", and the other end of the link might be: - Another USB host, when using USB "network" or "data transfer" cables. These are often used to network laptops to PCs, like "Laplink" parallel cables or some motherboards. These rely on specialized chips from many suppliers. - An intelligent USB gadget, perhaps embedding a Linux system. These include PDAs running Linux (iPaq, Yopy, Zaurus, and others), and devices that interoperate using the standard CDC-Ethernet specification (including many cable modems). - Network adapter hardware (like those for 10/100 Ethernet) which uses this driver framework. The link will appear with a name like "usb0", when the link is a two-node link, or "eth0" for most CDC-Ethernet devices. Those two-node links are most easily managed with Ethernet Bridging (CONFIG_BRIDGE) instead of routing. For more information see <http://www.linux-usb.org/usbnet/>. To compile this driver as a module, choose M here: the module will be called usbnet. config USB_NET_AX8817X tristate "ASIX AX88xxx Based USB 2.0 Ethernet Adapters" depends on USB_USBNET select CRC32 select PHYLIB default y help This option adds support for ASIX AX88xxx based USB 2.0 10/100 Ethernet adapters. This driver should work with at least the following devices: * Aten UC210T * ASIX AX88172 * Billionton Systems, USB2AR * Billionton Systems, GUSB2AM-1G-B * Buffalo LUA-U2-KTX * Corega FEther USB2-TX * D-Link DUB-E100 * Hawking UF200 * Linksys USB200M * Netgear FA120 * Sitecom LN-029 * Sitecom LN-028 * Intellinet USB 2.0 Ethernet * ST Lab USB 2.0 Ethernet * TrendNet TU2-ET100 This driver creates an interface named "ethX", where X depends on what other networking devices you have in use. config USB_NET_AX88179_178A tristate "ASIX AX88179/178A USB 3.0/2.0 to Gigabit Ethernet" depends on USB_USBNET select CRC32 select PHYLIB default y help This option adds support for ASIX AX88179 based USB 3.0/2.0 to Gigabit Ethernet adapters. This driver should work with at least the following devices: * ASIX AX88179 * ASIX AX88178A * Sitcomm LN-032 This driver creates an interface named "ethX", where X depends on what other networking devices you have in use. config USB_NET_CDCETHER tristate "CDC Ethernet support (smart devices such as cable modems)" depends on USB_USBNET default y help This option supports devices conforming to the Communication Device Class (CDC) Ethernet Control Model, a specification that's easy to implement in device firmware. The CDC specifications are available from <http://www.usb.org/>. CDC Ethernet is an implementation option for DOCSIS cable modems that support USB connectivity, used for non-Microsoft USB hosts. The Linux-USB CDC Ethernet Gadget driver is an open implementation. This driver should work with at least the following devices: * Dell Wireless 5530 HSPA * Ericsson PipeRider (all variants) * Ericsson Mobile Broadband Module (all variants) * Motorola (DM100 and SB4100) * Broadcom Cable Modem (reference design) * Toshiba (PCX1100U and F3507g/F3607gw) * ... This driver creates an interface named "ethX", where X depends on what other networking devices you have in use. However, if the IEEE 802 "local assignment" bit is set in the address, a "usbX" name is used instead. config USB_NET_CDC_EEM tristate "CDC EEM support" depends on USB_USBNET help This option supports devices conforming to the Communication Device Class (CDC) Ethernet Emulation Model, a specification that's easy to implement in device firmware. The CDC EEM specifications are available from <http://www.usb.org/>. This driver creates an interface named "ethX", where X depends on what other networking devices you have in use. However, if the IEEE 802 "local assignment" bit is set in the address, a "usbX" name is used instead. config USB_NET_CDC_NCM tristate "CDC NCM support" depends on USB_USBNET default y help This driver provides support for CDC NCM (Network Control Model Device USB Class Specification). The CDC NCM specification is available from <http://www.usb.org/>. Say "y" to link the driver statically, or "m" to build a dynamically linked module. This driver should work with at least the following devices: * ST-Ericsson M700 LTE FDD/TDD Mobile Broadband Modem (ref. design) * ST-Ericsson M5730 HSPA+ Mobile Broadband Modem (reference design) * ST-Ericsson M570 HSPA+ Mobile Broadband Modem (reference design) * ST-Ericsson M343 HSPA Mobile Broadband Modem (reference design) * Ericsson F5521gw Mobile Broadband Module config USB_NET_HUAWEI_CDC_NCM tristate "Huawei NCM embedded AT channel support" depends on USB_USBNET select USB_WDM select USB_NET_CDC_NCM help This driver supports huawei-style NCM devices, that use NCM as a transport for other protocols, usually an embedded AT channel. Good examples are: * Huawei E3131 * Huawei E3251 To compile this driver as a module, choose M here: the module will be called huawei_cdc_ncm.ko. config USB_NET_CDC_MBIM tristate "CDC MBIM support" depends on USB_USBNET select USB_WDM select USB_NET_CDC_NCM help This driver provides support for CDC MBIM (Mobile Broadband Interface Model) devices. The CDC MBIM specification is available from <http://www.usb.org/>. MBIM devices require configuration using the management protocol defined by the MBIM specification. This driver provides unfiltered access to the MBIM control channel through the associated /dev/cdc-wdmx character device. To compile this driver as a module, choose M here: the module will be called cdc_mbim. config USB_NET_DM9601 tristate "Davicom DM96xx based USB 10/100 ethernet devices" depends on USB_USBNET select CRC32 help This option adds support for Davicom DM9601/DM9620/DM9621A based USB 10/100 Ethernet adapters. config USB_NET_SR9700 tristate "CoreChip-sz SR9700 based USB 1.1 10/100 ethernet devices" depends on USB_USBNET select CRC32 help This option adds support for CoreChip-sz SR9700 based USB 1.1 10/100 Ethernet adapters. config USB_NET_SR9800 tristate "CoreChip-sz SR9800 based USB 2.0 10/100 ethernet devices" depends on USB_USBNET select CRC32 ---help--- Say Y if you want to use one of the following 100Mbps USB Ethernet device based on the CoreChip-sz SR9800 chip. This driver makes the adapter appear as a normal Ethernet interface, typically on eth0, if it is the only ethernet device, or perhaps on eth1, if you have a PCI or ISA ethernet card installed. To compile this driver as a module, choose M here: the module will be called sr9800. config USB_NET_SMSC75XX tristate "SMSC LAN75XX based USB 2.0 gigabit ethernet devices" depends on USB_USBNET select BITREVERSE select CRC16 select CRC32 help This option adds support for SMSC LAN75XX based USB 2.0 Gigabit Ethernet adapters. config USB_NET_SMSC95XX tristate "SMSC LAN95XX based USB 2.0 10/100 ethernet devices" depends on USB_USBNET select BITREVERSE select CRC16 select CRC32 help This option adds support for SMSC LAN95XX based USB 2.0 10/100 Ethernet adapters. config USB_NET_GL620A tristate "GeneSys GL620USB-A based cables" depends on USB_USBNET help Choose this option if you're using a host-to-host cable, or PC2PC motherboard, with this chip. Note that the half-duplex "GL620USB" is not supported. config USB_NET_NET1080 tristate "NetChip 1080 based cables (Laplink, ...)" default y depends on USB_USBNET help Choose this option if you're using a host-to-host cable based on this design: one NetChip 1080 chip and supporting logic, optionally with LEDs that indicate traffic config USB_NET_PLUSB tristate "Prolific PL-2301/2302/25A1/27A1 based cables" # if the handshake/init/reset problems, from original 'plusb', # are ever resolved ... then remove "experimental" depends on USB_USBNET help Choose this option if you're using a host-to-host cable with one of these chips. config USB_NET_MCS7830 tristate "MosChip MCS7830 based Ethernet adapters" depends on USB_USBNET help Choose this option if you're using a 10/100 Ethernet USB2 adapter based on the MosChip 7830 controller. This includes adapters marketed under the DeLOCK brand. config USB_NET_RNDIS_HOST tristate "Host for RNDIS and ActiveSync devices" depends on USB_USBNET select USB_NET_CDCETHER help This option enables hosting "Remote NDIS" USB networking links, as encouraged by Microsoft (instead of CDC Ethernet!) for use in various devices that may only support this protocol. A variant of this protocol (with even less public documentation) seems to be at the root of Microsoft's "ActiveSync" too. Avoid using this protocol unless you have no better options. The protocol specification is incomplete, and is controlled by (and for) Microsoft; it isn't an "Open" ecosystem or market. config USB_NET_CDC_SUBSET_ENABLE tristate depends on USB_NET_CDC_SUBSET config USB_NET_CDC_SUBSET tristate "Simple USB Network Links (CDC Ethernet subset)" depends on USB_USBNET default y help This driver module supports USB network devices that can work without any device-specific information. Select it if you have one of these drivers. Note that while many USB host-to-host cables can work in this mode, that may mean not being able to talk to Win32 systems or more commonly not being able to handle certain events (like replugging the host on the other end) very well. Also, these devices will not generally have permanently assigned Ethernet addresses. config USB_ALI_M5632 bool "ALi M5632 based 'USB 2.0 Data Link' cables" depends on USB_NET_CDC_SUBSET select USB_NET_CDC_SUBSET_ENABLE help Choose this option if you're using a host-to-host cable based on this design, which supports USB 2.0 high speed. config USB_AN2720 bool "AnchorChips 2720 based cables (Xircom PGUNET, ...)" depends on USB_NET_CDC_SUBSET select USB_NET_CDC_SUBSET_ENABLE help Choose this option if you're using a host-to-host cable based on this design. Note that AnchorChips is now a Cypress brand. config USB_BELKIN bool "eTEK based host-to-host cables (Advance, Belkin, ...)" depends on USB_NET_CDC_SUBSET select USB_NET_CDC_SUBSET_ENABLE default y help Choose this option if you're using a host-to-host cable based on this design: two NetChip 2890 chips and an Atmel microcontroller, with LEDs that indicate traffic. config USB_ARMLINUX bool "Embedded ARM Linux links (iPaq, ...)" depends on USB_NET_CDC_SUBSET select USB_NET_CDC_SUBSET_ENABLE default y help Choose this option to support the "usb-eth" networking driver used by most of the ARM Linux community with device controllers such as the SA-11x0 and PXA-25x UDCs, or the tftp capabilities in some PXA versions of the "blob" boot loader. Linux-based "Gumstix" PXA-25x based systems use this protocol to talk with other Linux systems. Although the ROMs shipped with Sharp Zaurus products use a different link level framing protocol, you can have them use this simpler protocol by installing a different kernel. config USB_EPSON2888 bool "Epson 2888 based firmware (DEVELOPMENT)" depends on USB_NET_CDC_SUBSET select USB_NET_CDC_SUBSET_ENABLE help Choose this option to support the usb networking links used by some sample firmware from Epson. config USB_KC2190 bool "KT Technology KC2190 based cables (InstaNet)" depends on USB_NET_CDC_SUBSET select USB_NET_CDC_SUBSET_ENABLE help Choose this option if you're using a host-to-host cable with one of these chips. config USB_NET_ZAURUS tristate "Sharp Zaurus (stock ROMs) and compatible" depends on USB_USBNET select USB_NET_CDCETHER select CRC32 default y help Choose this option to support the usb networking links used by Zaurus models like the SL-5000D, SL-5500, SL-5600, A-300, B-500. This also supports some related device firmware, as used in some PDAs from Olympus and some cell phones from Motorola. If you install an alternate image, such as the Linux 2.6 based versions of OpenZaurus, you should no longer need to support this protocol. Only the "eth-fd" or "net_fd" drivers in these devices really need this non-conformant variant of CDC Ethernet (or in some cases CDC MDLM) protocol, not "g_ether". config USB_NET_CX82310_ETH tristate "Conexant CX82310 USB ethernet port" depends on USB_USBNET help Choose this option if you're using a Conexant CX82310-based ADSL router with USB ethernet port. This driver is for routers only, it will not work with ADSL modems (use cxacru driver instead). config USB_NET_KALMIA tristate "Samsung Kalmia based LTE USB modem" depends on USB_USBNET help Choose this option if you have a Samsung Kalmia based USB modem as Samsung GT-B3730. To compile this driver as a module, choose M here: the module will be called kalmia. config USB_NET_QMI_WWAN tristate "QMI WWAN driver for Qualcomm MSM based 3G and LTE modems" depends on USB_USBNET select USB_WDM help Support WWAN LTE/3G devices based on Qualcomm Mobile Data Modem (MDM) chipsets. Examples of such devices are * Huawei E392/E398 This driver will only drive the ethernet part of the chips. The devices require additional configuration to be usable. Multiple management interfaces with linux drivers are available: * option: AT commands on /dev/ttyUSBx * cdc-wdm: Qualcomm MSM Interface (QMI) protocol on /dev/cdc-wdmx A modem manager with support for QMI is recommended. To compile this driver as a module, choose M here: the module will be called qmi_wwan. config USB_HSO tristate "Option USB High Speed Mobile Devices" depends on USB && RFKILL && TTY default n help Choose this option if you have an Option HSDPA/HSUPA card. These cards support downlink speeds of 7.2Mbps or greater. To compile this driver as a module, choose M here: the module will be called hso. config USB_NET_INT51X1 tristate "Intellon PLC based usb adapter" depends on USB_USBNET help Choose this option if you're using a 14Mb USB-based PLC (Powerline Communications) solution with an Intellon INT51x1/INT5200 chip, like the "devolo dLan duo". config USB_CDC_PHONET tristate "CDC Phonet support" depends on PHONET && USB_USBNET help Choose this option to support the Phonet interface to a Nokia cellular modem, as found on most Nokia handsets with the "PC suite" USB profile. config USB_IPHETH tristate "Apple iPhone USB Ethernet driver" default n ---help--- Module used to share Internet connection (tethering) from your iPhone (Original, 3G and 3GS) to your system. Note that you need userspace libraries and programs that are needed to pair your device with your system and that understand the iPhone protocol. For more information: http://giagio.com/wiki/moin.cgi/iPhoneEthernetDriver config USB_SIERRA_NET tristate "USB-to-WWAN Driver for Sierra Wireless modems" depends on USB_USBNET help Choose this option if you have a Sierra Wireless USB-to-WWAN device. To compile this driver as a module, choose M here: the module will be called sierra_net. config USB_VL600 tristate "LG VL600 modem dongle" depends on USB_NET_CDCETHER && TTY select USB_ACM help Select this if you want to use an LG Electronics 4G/LTE usb modem called VL600. This driver only handles the ethernet interface exposed by the modem firmware. To establish a connection you will first need a userspace program that sends the right command to the modem through its CDC ACM port, and most likely also a DHCP client. See this thread about using the 4G modem from Verizon: http://ubuntuforums.org/showpost.php?p=10589647&postcount=17 config USB_NET_CH9200 tristate "QingHeng CH9200 USB ethernet support" depends on USB_USBNET select MII help Choose this option if you have a USB ethernet adapter with a QinHeng CH9200 chipset. To compile this driver as a module, choose M here: the module will be called ch9200. endif # USB_NET_DRIVERS