D7net
Home
Console
Upload
information
Create File
Create Folder
About
Tools
:
/
lib
/
modules
/
4.4.0-1128-aws
/
build
/
arch
/
mips
/
txx9
/
Filename :
Kconfig
back
Copy
config MACH_TX39XX bool select MACH_TXX9 select SYS_HAS_CPU_TX39XX config MACH_TX49XX bool select MACH_TXX9 select CEVT_R4K select CSRC_R4K select IRQ_MIPS_CPU select SYS_HAS_CPU_TX49XX select SYS_SUPPORTS_64BIT_KERNEL config MACH_TXX9 bool select DMA_NONCOHERENT select SWAP_IO_SPACE select SYS_HAS_EARLY_PRINTK select SYS_SUPPORTS_32BIT_KERNEL select SYS_SUPPORTS_LITTLE_ENDIAN select SYS_SUPPORTS_BIG_ENDIAN select HAVE_CLK config TOSHIBA_JMR3927 bool "Toshiba JMR-TX3927 board" depends on MACH_TX39XX select SOC_TX3927 config TOSHIBA_RBTX4927 bool "Toshiba RBTX49[23]7 board" depends on MACH_TX49XX select SOC_TX4927 # TX4937 is subset of TX4938 select SOC_TX4938 help This Toshiba board is based on the TX4927 processor. Say Y here to support this machine type config TOSHIBA_RBTX4938 bool "Toshiba RBTX4938 board" depends on MACH_TX49XX select SOC_TX4938 help This Toshiba board is based on the TX4938 processor. Say Y here to support this machine type config TOSHIBA_RBTX4939 bool "Toshiba RBTX4939 board" depends on MACH_TX49XX select SOC_TX4939 select TXX9_7SEGLED help This Toshiba board is based on the TX4939 processor. Say Y here to support this machine type config SOC_TX3927 bool select CEVT_TXX9 select HAS_TXX9_SERIAL select HW_HAS_PCI select IRQ_TXX9 select GPIO_TXX9 config SOC_TX4927 bool select CEVT_TXX9 select HAS_TXX9_SERIAL select HW_HAS_PCI select IRQ_TXX9 select PCI_TX4927 select GPIO_TXX9 select HAS_TXX9_ACLC config SOC_TX4938 bool select CEVT_TXX9 select HAS_TXX9_SERIAL select HW_HAS_PCI select IRQ_TXX9 select PCI_TX4927 select GPIO_TXX9 select HAS_TXX9_ACLC config SOC_TX4939 bool select CEVT_TXX9 select HAS_TXX9_SERIAL select HW_HAS_PCI select PCI_TX4927 select HAS_TXX9_ACLC config TXX9_7SEGLED bool config TOSHIBA_FPCIB0 bool "FPCIB0 Backplane Support" depends on PCI && MACH_TXX9 select I8259 config PICMG_PCI_BACKPLANE_DEFAULT bool "Support for PICMG PCI Backplane" depends on PCI && MACH_TXX9 default y if !TOSHIBA_FPCIB0 if TOSHIBA_RBTX4938 comment "Multiplex Pin Select" choice prompt "PIO[58:61]" default TOSHIBA_RBTX4938_MPLEX_PIO58_61 config TOSHIBA_RBTX4938_MPLEX_PIO58_61 bool "PIO" config TOSHIBA_RBTX4938_MPLEX_NAND bool "NAND" config TOSHIBA_RBTX4938_MPLEX_ATA bool "ATA" config TOSHIBA_RBTX4938_MPLEX_KEEP bool "Keep firmware settings" endchoice endif config PCI_TX4927 bool