D7net
Home
Console
Upload
information
Create File
Create Folder
About
Tools
:
/
lib
/
modules
/
4.4.0-1128-aws
/
build
/
arch
/
arm
/
mach-imx
/
Filename :
Kconfig
back
Copy
menuconfig ARCH_MXC bool "Freescale i.MX family" if ARCH_MULTI_V4_V5 || ARCH_MULTI_V6_V7 || ARM_SINGLE_ARMV7M select ARCH_REQUIRE_GPIOLIB select ARM_CPU_SUSPEND if PM select CLKSRC_IMX_GPT select GENERIC_IRQ_CHIP select PINCTRL select PM_OPP if PM select SOC_BUS select SRAM help Support for Freescale MXC/iMX-based family of processors if ARCH_MXC config MXC_TZIC bool config MXC_AVIC bool config MXC_DEBUG_BOARD bool "Enable MXC debug board(for 3-stack)" depends on MACH_MX27_3DS || MACH_MX31_3DS || MACH_MX35_3DS help The debug board is an integral part of the MXC 3-stack(PDK) platforms, it can be attached or removed from the peripheral board. On debug board, several debug devices(ethernet, UART, buttons, LEDs and JTAG) are implemented. Between the MCU and these devices, a CPLD is added as a bridge which performs data/address de-multiplexing and decode, signal level shift, interrupt control and various board functions. config HAVE_EPIT bool config MXC_USE_EPIT bool "Use EPIT instead of GPT" depends on HAVE_EPIT help Use EPIT as the system timer on systems that have it. Normally you don't have a reason to do so as the EPIT has the same features and uses the same clocks as the GPT. Anyway, on some systems the GPT may be in use for other purposes. config ARCH_HAS_RNGA bool config HAVE_IMX_ANATOP bool config HAVE_IMX_GPC bool select PM_GENERIC_DOMAINS if PM config HAVE_IMX_MMDC bool config HAVE_IMX_SRC def_bool y if SMP select ARCH_HAS_RESET_CONTROLLER config IMX_HAVE_IOMUX_V1 bool config ARCH_MXC_IOMUX_V3 bool config SOC_IMX1 bool select CPU_ARM920T select IMX_HAVE_IOMUX_V1 select MXC_AVIC select PINCTRL_IMX1 config SOC_IMX21 bool select CPU_ARM926T select IMX_HAVE_IOMUX_V1 select MXC_AVIC config SOC_IMX27 bool select CPU_ARM926T select IMX_HAVE_IOMUX_V1 select MXC_AVIC select PINCTRL_IMX27 config SOC_IMX31 bool select CPU_V6 select IMX_HAVE_PLATFORM_MXC_RNGA select MXC_AVIC select SMP_ON_UP if SMP config SOC_IMX35 bool select ARCH_MXC_IOMUX_V3 select HAVE_EPIT select MXC_AVIC select PINCTRL_IMX35 select SMP_ON_UP if SMP if ARCH_MULTI_V4T comment "MX1 platforms:" config MACH_SCB9328 bool "Synertronixx scb9328" select IMX_HAVE_PLATFORM_IMX_UART select SOC_IMX1 help Say Y here if you are using a Synertronixx scb9328 board config MACH_APF9328 bool "APF9328" select IMX_HAVE_PLATFORM_IMX_I2C select IMX_HAVE_PLATFORM_IMX_UART select SOC_IMX1 help Say Yes here if you are using the Armadeus APF9328 development board config MACH_IMX1_DT bool "Support i.MX1 platforms from device tree" select SOC_IMX1 help Include support for Freescale i.MX1 based platforms using the device tree for discovery. endif if ARCH_MULTI_V5 comment "MX21 platforms:" config MACH_MX21ADS bool "MX21ADS platform" select IMX_HAVE_PLATFORM_IMX_FB select IMX_HAVE_PLATFORM_IMX_UART select IMX_HAVE_PLATFORM_MXC_MMC select IMX_HAVE_PLATFORM_MXC_NAND select SOC_IMX21 help Include support for MX21ADS platform. This includes specific configurations for the board and its peripherals. comment "MX27 platforms:" config MACH_MX27ADS bool "MX27ADS platform" select IMX_HAVE_PLATFORM_IMX_FB select IMX_HAVE_PLATFORM_IMX_I2C select IMX_HAVE_PLATFORM_IMX_UART select IMX_HAVE_PLATFORM_MXC_MMC select IMX_HAVE_PLATFORM_MXC_NAND select IMX_HAVE_PLATFORM_MXC_W1 select SOC_IMX27 help Include support for MX27ADS platform. This includes specific configurations for the board and its peripherals. config MACH_MX27_3DS bool "MX27PDK platform" select IMX_HAVE_PLATFORM_FSL_USB2_UDC select IMX_HAVE_PLATFORM_IMX2_WDT select IMX_HAVE_PLATFORM_IMX_FB select IMX_HAVE_PLATFORM_IMX_I2C select IMX_HAVE_PLATFORM_IMX_KEYPAD select IMX_HAVE_PLATFORM_IMX_SSI select IMX_HAVE_PLATFORM_IMX_UART select IMX_HAVE_PLATFORM_MX2_CAMERA select IMX_HAVE_PLATFORM_MXC_EHCI select IMX_HAVE_PLATFORM_MXC_MMC select IMX_HAVE_PLATFORM_SPI_IMX select MXC_DEBUG_BOARD select USB_ULPI_VIEWPORT if USB_ULPI select SOC_IMX27 help Include support for MX27PDK platform. This includes specific configurations for the board and its peripherals. config MACH_IMX27_VISSTRIM_M10 bool "Vista Silicon i.MX27 Visstrim_m10" select IMX_HAVE_PLATFORM_GPIO_KEYS select IMX_HAVE_PLATFORM_IMX_I2C select IMX_HAVE_PLATFORM_IMX_SSI select IMX_HAVE_PLATFORM_IMX_UART select IMX_HAVE_PLATFORM_MX2_CAMERA select IMX_HAVE_PLATFORM_MX2_EMMA select IMX_HAVE_PLATFORM_MXC_EHCI select IMX_HAVE_PLATFORM_MXC_MMC select LEDS_GPIO_REGISTER select SOC_IMX27 help Include support for Visstrim_m10 platform and its different variants. This includes specific configurations for the board and its peripherals. config MACH_PCA100 bool "Phytec phyCARD-s (pca100)" select IMX_HAVE_PLATFORM_FSL_USB2_UDC select IMX_HAVE_PLATFORM_IMX2_WDT select IMX_HAVE_PLATFORM_IMX_FB select IMX_HAVE_PLATFORM_IMX_I2C select IMX_HAVE_PLATFORM_IMX_SSI select IMX_HAVE_PLATFORM_IMX_UART select IMX_HAVE_PLATFORM_MXC_EHCI select IMX_HAVE_PLATFORM_MXC_MMC select IMX_HAVE_PLATFORM_MXC_NAND select IMX_HAVE_PLATFORM_MXC_W1 select IMX_HAVE_PLATFORM_SPI_IMX select USB_ULPI_VIEWPORT if USB_ULPI select SOC_IMX27 help Include support for phyCARD-s (aka pca100) platform. This includes specific configurations for the module and its peripherals. config MACH_IMX27_DT bool "Support i.MX27 platforms from device tree" select SOC_IMX27 help Include support for Freescale i.MX27 based platforms using the device tree for discovery endif if ARCH_MULTI_V6 comment "MX31 platforms:" config MACH_MX31ADS bool "Support MX31ADS platforms" default y select IMX_HAVE_PLATFORM_IMX_I2C select IMX_HAVE_PLATFORM_IMX_SSI select IMX_HAVE_PLATFORM_IMX_UART select SOC_IMX31 help Include support for MX31ADS platform. This includes specific configurations for the board and its peripherals. config MACH_MX31ADS_WM1133_EV1 bool "Support Wolfson Microelectronics 1133-EV1 module" depends on MACH_MX31ADS depends on MFD_WM8350_I2C depends on REGULATOR_WM8350 = y help Include support for the Wolfson Microelectronics 1133-EV1 PMU and audio module for the MX31ADS platform. config MACH_MX31LILLY bool "Support MX31 LILLY-1131 platforms (INCO startec)" select IMX_HAVE_PLATFORM_IMX_UART select IMX_HAVE_PLATFORM_IPU_CORE select IMX_HAVE_PLATFORM_MXC_EHCI select IMX_HAVE_PLATFORM_MXC_MMC select IMX_HAVE_PLATFORM_SPI_IMX select USB_ULPI_VIEWPORT if USB_ULPI select SOC_IMX31 help Include support for mx31 based LILLY1131 modules. This includes specific configurations for the board and its peripherals. config MACH_MX31LITE bool "Support MX31 LITEKIT (LogicPD)" select IMX_HAVE_PLATFORM_IMX2_WDT select IMX_HAVE_PLATFORM_IMX_UART select IMX_HAVE_PLATFORM_MXC_EHCI select IMX_HAVE_PLATFORM_MXC_MMC select IMX_HAVE_PLATFORM_MXC_NAND select IMX_HAVE_PLATFORM_MXC_RTC select IMX_HAVE_PLATFORM_SPI_IMX select LEDS_GPIO_REGISTER select USB_ULPI_VIEWPORT if USB_ULPI select SOC_IMX31 help Include support for MX31 LITEKIT platform. This includes specific configurations for the board and its peripherals. config MACH_PCM037 bool "Support Phytec pcm037 (i.MX31) platforms" select IMX_HAVE_PLATFORM_FSL_USB2_UDC select IMX_HAVE_PLATFORM_IMX2_WDT select IMX_HAVE_PLATFORM_IMX_I2C select IMX_HAVE_PLATFORM_IMX_UART select IMX_HAVE_PLATFORM_IPU_CORE select IMX_HAVE_PLATFORM_MXC_EHCI select IMX_HAVE_PLATFORM_MXC_MMC select IMX_HAVE_PLATFORM_MXC_NAND select IMX_HAVE_PLATFORM_MXC_W1 select USB_ULPI_VIEWPORT if USB_ULPI select SOC_IMX31 help Include support for Phytec pcm037 platform. This includes specific configurations for the board and its peripherals. config MACH_PCM037_EET bool "Support pcm037 EET board extensions" depends on MACH_PCM037 select IMX_HAVE_PLATFORM_GPIO_KEYS select IMX_HAVE_PLATFORM_SPI_IMX help Add support for PCM037 EET baseboard extensions. If you are using the OLED display with EET, use "video=mx3fb:CMEL-OLED" kernel command-line parameter. config MACH_MX31_3DS bool "Support MX31PDK (3DS)" select IMX_HAVE_PLATFORM_FSL_USB2_UDC select IMX_HAVE_PLATFORM_IMX2_WDT select IMX_HAVE_PLATFORM_IMX_I2C select IMX_HAVE_PLATFORM_IMX_KEYPAD select IMX_HAVE_PLATFORM_IMX_SSI select IMX_HAVE_PLATFORM_IMX_UART select IMX_HAVE_PLATFORM_IPU_CORE select IMX_HAVE_PLATFORM_MXC_EHCI select IMX_HAVE_PLATFORM_MXC_MMC select IMX_HAVE_PLATFORM_MXC_NAND select IMX_HAVE_PLATFORM_SPI_IMX select MXC_DEBUG_BOARD select USB_ULPI_VIEWPORT if USB_ULPI select SOC_IMX31 help Include support for MX31PDK (3DS) platform. This includes specific configurations for the board and its peripherals. config MACH_MX31_3DS_MXC_NAND_USE_BBT bool "Make the MXC NAND driver use the in flash Bad Block Table" depends on MACH_MX31_3DS depends on MTD_NAND_MXC help Enable this if you want that the MXC NAND driver uses the in flash Bad Block Table to know what blocks are bad instead of scanning the entire flash looking for bad block markers. config MACH_MX31MOBOARD bool "Support mx31moboard platforms (EPFL Mobots group)" select IMX_HAVE_PLATFORM_FSL_USB2_UDC select IMX_HAVE_PLATFORM_IMX2_WDT select IMX_HAVE_PLATFORM_IMX_I2C select IMX_HAVE_PLATFORM_IMX_SSI select IMX_HAVE_PLATFORM_IMX_UART select IMX_HAVE_PLATFORM_IPU_CORE select IMX_HAVE_PLATFORM_MXC_EHCI select IMX_HAVE_PLATFORM_MXC_MMC select IMX_HAVE_PLATFORM_SPI_IMX select LEDS_GPIO_REGISTER select USB_ULPI_VIEWPORT if USB_ULPI select SOC_IMX31 help Include support for mx31moboard platform. This includes specific configurations for the board and its peripherals. config MACH_QONG bool "Support Dave/DENX QongEVB-LITE platform" select IMX_HAVE_PLATFORM_IMX2_WDT select IMX_HAVE_PLATFORM_IMX_UART select SOC_IMX31 help Include support for Dave/DENX QongEVB-LITE platform. This includes specific configurations for the board and its peripherals. config MACH_ARMADILLO5X0 bool "Support Atmark Armadillo-500 Development Base Board" select IMX_HAVE_PLATFORM_GPIO_KEYS select IMX_HAVE_PLATFORM_IMX_I2C select IMX_HAVE_PLATFORM_IMX_UART select IMX_HAVE_PLATFORM_IPU_CORE select IMX_HAVE_PLATFORM_MXC_EHCI select IMX_HAVE_PLATFORM_MXC_MMC select IMX_HAVE_PLATFORM_MXC_NAND select USB_ULPI_VIEWPORT if USB_ULPI select SOC_IMX31 help Include support for Atmark Armadillo-500 platform. This includes specific configurations for the board and its peripherals. config MACH_KZM_ARM11_01 bool "Support KZM-ARM11-01(Kyoto Microcomputer)" select IMX_HAVE_PLATFORM_IMX_UART select SOC_IMX31 help Include support for KZM-ARM11-01. This includes specific configurations for the board and its peripherals. config MACH_BUG bool "Support Buglabs BUGBase platform" default y select IMX_HAVE_PLATFORM_IMX_UART select SOC_IMX31 help Include support for BUGBase 1.3 platform. This includes specific configurations for the board and its peripherals. config MACH_IMX31_DT bool "Support i.MX31 platforms from device tree" select SOC_IMX31 help Include support for Freescale i.MX31 based platforms using the device tree for discovery. comment "MX35 platforms:" config MACH_IMX35_DT bool "Support i.MX35 platforms from device tree" select SOC_IMX35 help Include support for Freescale i.MX35 based platforms using the device tree for discovery. config MACH_PCM043 bool "Support Phytec pcm043 (i.MX35) platforms" select IMX_HAVE_PLATFORM_FLEXCAN select IMX_HAVE_PLATFORM_FSL_USB2_UDC select IMX_HAVE_PLATFORM_IMX2_WDT select IMX_HAVE_PLATFORM_IMX_I2C select IMX_HAVE_PLATFORM_IMX_SSI select IMX_HAVE_PLATFORM_IMX_UART select IMX_HAVE_PLATFORM_IPU_CORE select IMX_HAVE_PLATFORM_MXC_EHCI select IMX_HAVE_PLATFORM_MXC_NAND select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX select USB_ULPI_VIEWPORT if USB_ULPI select SOC_IMX35 help Include support for Phytec pcm043 platform. This includes specific configurations for the board and its peripherals. config MACH_MX35_3DS bool "Support MX35PDK platform" select IMX_HAVE_PLATFORM_FSL_USB2_UDC select IMX_HAVE_PLATFORM_IMX2_WDT select IMX_HAVE_PLATFORM_IMX_FB select IMX_HAVE_PLATFORM_IMX_I2C select IMX_HAVE_PLATFORM_IMX_UART select IMX_HAVE_PLATFORM_IPU_CORE select IMX_HAVE_PLATFORM_MXC_EHCI select IMX_HAVE_PLATFORM_MXC_NAND select IMX_HAVE_PLATFORM_MXC_RTC select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX select MXC_DEBUG_BOARD select SOC_IMX35 help Include support for MX35PDK platform. This includes specific configurations for the board and its peripherals. config MACH_VPR200 bool "Support VPR200 platform" select IMX_HAVE_PLATFORM_FSL_USB2_UDC select IMX_HAVE_PLATFORM_GPIO_KEYS select IMX_HAVE_PLATFORM_IMX2_WDT select IMX_HAVE_PLATFORM_IMX_I2C select IMX_HAVE_PLATFORM_IMX_UART select IMX_HAVE_PLATFORM_IPU_CORE select IMX_HAVE_PLATFORM_MXC_EHCI select IMX_HAVE_PLATFORM_MXC_NAND select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX select SOC_IMX35 help Include support for VPR200 platform. This includes specific configurations for the board and its peripherals. endif comment "Device tree only" if ARCH_MULTI_V5 config SOC_IMX25 bool "i.MX25 support" select ARCH_MXC_IOMUX_V3 select CPU_ARM926T select MXC_AVIC select PINCTRL_IMX25 help This enables support for Freescale i.MX25 processor endif if ARCH_MULTI_V7 comment "Cortex-A platforms" config SOC_IMX5 bool select HAVE_IMX_SRC select MXC_TZIC config SOC_IMX50 bool "i.MX50 support" select PINCTRL_IMX50 select SOC_IMX5 help This enables support for Freescale i.MX50 processor. config SOC_IMX51 bool "i.MX51 support" select PINCTRL_IMX51 select SOC_IMX5 help This enables support for Freescale i.MX51 processor config SOC_IMX53 bool "i.MX53 support" select PINCTRL_IMX53 select SOC_IMX5 help This enables support for Freescale i.MX53 processor. config SOC_IMX6 bool select ARM_ERRATA_754322 select ARM_ERRATA_775420 select ARM_GIC select HAVE_IMX_ANATOP select HAVE_IMX_GPC select HAVE_IMX_MMDC select HAVE_IMX_SRC select MFD_SYSCON select PL310_ERRATA_769419 if CACHE_L2X0 config SOC_IMX6Q bool "i.MX6 Quad/DualLite support" select ARM_ERRATA_764369 if SMP select HAVE_ARM_SCU if SMP select HAVE_ARM_TWD if SMP select PCI_DOMAINS if PCI select PINCTRL_IMX6Q select SOC_IMX6 help This enables support for Freescale i.MX6 Quad processor. config SOC_IMX6SL bool "i.MX6 SoloLite support" select PINCTRL_IMX6SL select SOC_IMX6 help This enables support for Freescale i.MX6 SoloLite processor. config SOC_IMX6SX bool "i.MX6 SoloX support" select PINCTRL_IMX6SX select SOC_IMX6 help This enables support for Freescale i.MX6 SoloX processor. config SOC_IMX6UL bool "i.MX6 UltraLite support" select PINCTRL_IMX6UL select SOC_IMX6 help This enables support for Freescale i.MX6 UltraLite processor. config SOC_IMX7D bool "i.MX7 Dual support" select PINCTRL_IMX7D select ARM_GIC select HAVE_IMX_ANATOP select HAVE_IMX_MMDC select HAVE_IMX_SRC help This enables support for Freescale i.MX7 Dual processor. config SOC_LS1021A bool "Freescale LS1021A support" select ARM_GIC select HAVE_ARM_ARCH_TIMER select PCI_DOMAINS if PCI select ZONE_DMA if ARM_LPAE help This enables support for Freescale LS1021A processor. endif comment "Cortex-A/Cortex-M asymmetric multiprocessing platforms" if ARCH_MULTI_V7 || ARM_SINGLE_ARMV7M config SOC_VF610 bool "Vybrid Family VF610 support" select ARM_GIC if ARCH_MULTI_V7 select PINCTRL_VF610 select PL310_ERRATA_769419 if CACHE_L2X0 select SMP_ON_UP if SMP help This enables support for Freescale Vybrid VF610 processor. choice prompt "Clocksource for scheduler clock" depends on SOC_VF610 default VF_USE_ARM_GLOBAL_TIMER config VF_USE_ARM_GLOBAL_TIMER bool "Use ARM Global Timer" if ARCH_MULTI_V7 select ARM_GLOBAL_TIMER select CLKSRC_ARM_GLOBAL_TIMER_SCHED_CLOCK help Use the ARM Global Timer as clocksource config VF_USE_PIT_TIMER bool "Use PIT timer" select VF_PIT_TIMER help Use SoC Periodic Interrupt Timer (PIT) as clocksource endchoice endif source "arch/arm/mach-imx/devices/Kconfig" endif